收藏本站
NCL30000
Overview
Figure 2 illustrates how the NCL30000 is configured to
implement an isolated power factor corrected flyback
switch mode power supply. On the secondary side is the
NCS1002, a constant voltage, constant current controller
which senses the average LED current and the output
voltage and provides a feedback control signal to the
primary side through an opto-coupler interface. One of the
key benefits of active power factor correction is that it makes
the load appear like a linear resistance similar to an
incandescent bulb. High power factor requires generally
sinusoidal line current and minimal phase displacement
between the line current and voltage. The NCL30000
operates in a fixed on-time variable frequency mode where
Table 2. MAXIMUM RATINGS
the power switch is on for the same length of time over a half
cycle of input power. The current in the primary of the
transformer starts at zero each switching cycle and is directly
proportional to the applied voltage times the on-time.
Therefore with a fixed on-time, the current will follow the
applied voltage generating a current of the same shape. Just
as in a traditional boost PFC circuit, the control bandwidth
is low so that the on-time is constant throughout a single line
cycle. The feedback signal from the secondary side is used
to modify the average on-time so the current through the
LEDs is properly regulated regardless of forward voltage
variation of the LED string.
MFP Voltage
MFP Current
COMP Voltage
COMP Current
Ct Voltage
Ct Current
CS Voltage
CS Current
ZCD Voltage
ZCD Current
DRV Voltage
DRV Sink Current
DRV Source Current
Supply Voltage
Supply Current
Rating
Symbol
V MFP
I MFP
V Control
I Control
V Ct
I Ct
V CS
I CS
V ZCD
I ZCD
V DRV
I DRV(sink)
I DRV(source)
V CC
I CC
Value
? 0.3 to 10
? 10
? 0.3 to 6.5
? 2 to 10
? 0.3 to 6
? 10
? 0.3 to 6
? 10
? 0.3 to 10
? 10
? 0.3 to V CC
800
500
? 0.3 to 20
? 20
Unit
V
mA
V
mA
V
mA
V
mA
V
mA
V
mA
mA
V
mA
Power Dissipation (T A = 70 ? C, 2.0 Oz Cu, 55
mm 2
Printed Circuit Copper Clad)
P D
450
mW
Thermal Resistance Junction-to-Ambient
(2.0 Oz Cu, 55 mm 2 Printed Circuit Copper Clad)
Junction-to-Air, Low conductivity PCB (Note 3)
Junction-to-Air, High conductivity PCB (Note 4)
Operating Junction Temperature Range
Maximum Junction Temperature
Storage Temperature Range
Lead Temperature (Soldering, 10 s)
R q JA
R q JA
R q JA
T J
T J(MAX)
T STG
T L
178
168
127
? 40 to 125
150
? 65 to 150
300
? C/W
? C
? C
? C
? C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. This device series contains ESD protection and exceeds the following tests:
Pins 1–8: Human Body Model 2000 V per JEDEC Standard JESD22 ? A114E.
Pins 1– 8: Machine Model Method 200 V per JEDEC Standard JESD22 ? A115 ? A.
2. This device contains Latch-up protection and exceeds ? 100 mA per JEDEC Standard JESD78.
3. As mounted on a 40 ? 40 ? 1.5 mm FR4 substrate with a single layer of 80 mm 2 of 2 oz copper traces and heat spreading area. As specified
for a JEDEC 51 low conductivity test PCB. Test conditions were under natural convection or zero air flow.
4. As mounted on a 40 ? 40 ? 1.5 mm FR4 substrate with a single layer of 650 mm 2 of 2 oz copper traces and heat spreading area. As specified
for a JEDEC 51 high conductivity test PCB. Test conditions were under natural convection or zero air flow.
http://onsemi.com
4
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCL30051LEDGEVB BOARD EVAL NCL30051 LED DRIVER
NCL30100ASLDGEVB BOARD DEMO SGL LAYER PWM DIM LED
NCL30105GEVB BOARD EVAL 80V 350 FOR LED DRV
NCP1013LEDGEVB BOARD EVAL 5W UNIV LED DRIVER
NCP1028LEDGEVB EVAL BOARD FOR NCP1028LEDG
NCP1216AFORWGEVB BOARD EVAL NCP1216A 35W
NCP1351LEDGEVB EVAL BOARD FOR NCP1351LEDG
NCP3065BBGEVB BOARD EVAL NCP3065 MR16 BOOST
相关代理商/技术参数
NCL30001 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:High-Efficiency Single Stage Power Factor Correction and Step-Down Offline LED Driver
NCL30001DR2G 功能描述:LED照明驱动器 ANA PFC CONTROLLER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
NCL30001DR2G-CUT TAPE 制造商:ON 功能描述:NCL30001 Series 11.3 V Isolated Step-Down Single Stage Power Factor - SOIC-16
NCL30001LEDGEVB 功能描述:LED 照明开发工具 Programmers Development RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
NCL30002 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Power Factor Corrected Buck LED Driver
NCL30002DIM1GEVB 制造商:ON Semiconductor 功能描述:120V DIMMABLE HPF BUCK - Bulk
NCL30002DIM2GEVB 制造商:ON Semiconductor 功能描述:230V DIMMABLE HPF BUCK - Bulk
NCL30002DR2G 功能描述:LED照明驱动器 Power Factor Offline Buck LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N